Dual effect synergistically triggered Ce:(Y,Tb)3(Al,Mn)5O12 transparent ceramics enabling a high color-rendering index and excellent thermal stability for white LEDs

Ce:Y₃Al₅O₁₂ transparent ceramics (TCs) with appropriate emission light proportion and high thermal stability are significant to construct white light emitting diode devices with excellent chromaticity parameters. In this work, strategies of controlling crystal-field splitting around Ce³⁺ ion and doping orange-red emitting ion, were adopted to fabricate Ce:(Y,Tb)₃(Al,Mn)₅O₁₂ TCs via vacuum sintering technique. Notably, 85.4 % of the room-temperature luminescence intensity of the TC was retained at 150 °C, and the color rendering index was as high as 79.8. Furthermore, a 12 nm red shift and a 16.2 % increase of full width at half maximum were achieved owing to the synergistic effects of Tb³⁺ and Mn²⁺ ions. By combining TCs with a 460 nm blue chip, a warm white light with a low correlated color temperature of 4155 K was acquired. Meanwhile, the action mechanism of Tb³⁺ ion and the energy transfer between Ce³⁺ and Mn²⁺ ions were verified in prepared TCs.     

Microstructure and properties of WC-12Co composite coatings prepared by laser cladding

A comprehensive study of the phase composition, microstructure evolution, microhardness and wear performance of WC-12Co composite coatings fabricated by laser cladding using coaxial powder-feed mode was presented. It was shown that a combination of high scan speed and high laser energy density made WC on the edge of WC-12Co composite powders partially melt in liquid Co and 304 stainless steel matrix, and then new carbides consisting of lamellar WC and herringbone M₃W₃C (M=Fe, Co) were formed. Meanwhile, WC-12Co composite coatings with no porosity, cracks and drawbacks like decarburization were obtained, showing high densification and good metallurgical bonding with the substrate. Furthermore, a considerably high microhardness of HV_0.3 1500-1600, low coefficient of friction of 0.55 and wear rate of (2.15±0.31)×10^-7 mm³/(N·m) were achieved owing to the synergistic effect of excellent metallurgical bonding and fine microstructures of composite coating under laser power of 1500 W.     

Ultrasonic-vibration-assisted laser annealing of fluorine-doped tin oxide thin films for improving optical and electrical properties: Overlapping rate optimization

An ultrasonic-vibration-assisted laser annealing method was developed to enhance the performance of fluorine-doped tin oxide (FTO) thin films. The influences of ultrasonic vibration, laser scan line overlapping rate (L_OR) and laser spot overlapping rate (S_OR) on surface morphology, FTO layer thickness, RMS roughness, crystal structure and photoelectric properties of the FTO films were investigated. The results indicated that the presence of ultrasonic vibration during laser annealing could significantly enhance the film compactness, and using moderate L_OR and S_OR values resulted in significantly decreased FTO layer thicknesses and RMS roughnesses as well as slightly increased crystallite sizes, thus yielding significantly improved optical transmittance values and slightly enhanced electrical conductivity values. It was found that the optimal L_OR and S_OR values for ultrasonic-vibration-assisted laser annealing of the FTO films were 80% and 90%, respectively. The as-obtained film possessed the best overall photoelectric property with an average transmittance (400–800?nm) of 85.9%, a sheet resistance of 8.7?Ω/sq and a figure of merit of 2.51?×?10^–2 Ω^–1. This work may be of great significance in terms of performance optimization of transparent conducting oxide (TCO) thin films.     

Development and investigations on a hybrid tooling concept for coaxial and concurrent application of electrochemical and laser micromachining processes

In hybrid laser-electrochemical micromachining, both laser and electrochemical process energies act along the same machining axis and thus both influence material removal by their interaction. The traditional nozzle based laser assisted jet-ECM concepts require laser to be focused on workpiece surface in an electrochemical environment and are limited in aspect ratios as the nozzle stays above the workpiece surface. In this work, a hybrid tooling concept is proposed for a novel process scheme of precision hybrid laser-electrochemical micromachining. The tool serves the function of both an ECM electrode as well as a leaky-type multimode waveguide for the laser and delivers laser homogeneously together with the electrolyte on the workpiece surface without requiring laser to be focused on the workpiece surface. A precision prototype hybrid machine-tool is developed which employs short pulsed nano-second laser and micro-second pulsed voltage source for precision micromachining. For this system, ray tracing and detailed multiphysics electrochemical micromachining process simulations are carried out to demonstrate the applicability of this hybrid tooling concept and explain the shape evolution. Successful experimental realization of coaxial and concurrent application of electrochemical and laser processes is presented. Prototype tool electrodes are fabricated and experiments are carried out on an in-house developed prototype hybrid machine tool. The results reveal that the proposed hybrid tool is successfully capable of concentrating laser and electrochemical process energies simultaneously in the same machining zone. However, with the initial design of this hybrid tool, a maximum of 30–40% of laser power is available in the machining zone. Some suggestions for further research will be presented.     

New semi-conducting poly(phenylene vinylene-alt-anthrylene vinylene)s: Synthesis,characterization and photophysical properties

An anthracene-based semi-conducting polymer (P1) and its cyano-analogue (P2) were synthesized via the Wittig and Knoevenagel polycondensations. The polymers were soluble in common organic solvents and have number-average molecular weights of 13,750 and 6430 g mol⁻¹ for P1 and P2, respectively. The DSC analyzes show a good thermal stability and an amorphous morphology in solid state for these organic materials. The optical properties of the polymers were investigated by UV–visible absorption and fluorescence spectroscopies. The HOMO and LUMO levels were estimated using cyclic voltammetry analysis. The effect of cyano group on the photophysical properties of poly(phenylene vinylene-alt-anthrylene vinylene)s was investigated. The results demonstrate an enhancement in the ionization potential and a significant improvement of the fluorescence yield due to introduction of such groups into the π-conjugated system. Single-layer diodes based on these organic semiconductors have been fabricated and showed relatively low turn-on voltages.     

Acceptance of biomass plants – Results of a longitudinal study in the bioenergy-region Altmark

The present contribution addresses the results of a longitudinal study in a ‘bioenergy-region’ concerning the public acceptance of biomass plants and the corresponding influencing factors. Using a standardized questionnaire, 423 persons were polled between 2009 and 2011 on three points of measurement in four places in the bioenergy-region Altmark. One main result of the study is that the reported public acceptance remains constantly high over time; nevertheless it became evident that the respective influencing factors differ in their strength, whereas the perceived regional benefit shows a strong connection to the reported public acceptance of biomass plants at each point of measurement. Concluding the research results, the acceptance of biomass plants doesn't seem to be a fixed construct, but has to be seen in context of the respective experiences with plants on a local level over time.In addition to the local population, key actors of the regional biomass sector were also interviewed (N = 26). The analyses show significant differences in the perception and evaluation of the current informational level between the population and the key actors. Furthermore, the key actors estimated the utilisation of biomass even more positively and expected a greater ‘signal function’ of the bioenergy-region-project compared to the population.     

Femtosecond laser micro-milling dental glass ceramics: An experimental analysis and COMSOL finite element simulation

Dental glass ceramic materials are widely used in all-ceramic restoration technology. In order to effectively solve the problems existing in the process of traditional diamond cutter milling dental glass ceramic materials, such as severe needle loss, large tool wear and general milling efficiency, a new method of ultrafast laser milling dental glass ceramics is proposed. In this paper, 1030 nm femtosecond laser with pulse width of 600fs was used to micro-mill dental glass ceramics. Confocal laser microscopy was used to measure the milling depth and surface roughness of single-layer milling under selected laser processing parameters. The pre-layered milling software was developed to control the z-axis lifting and to compensate the focal length synchronously. Scanning electron microscope (SEM), Raman spectrometer and Vickers micro-hardness tester were used to characterize the dental glass ceramics after femtosecond laser milling. The results showed that under the specific laser processing parameters, the infrared femtosecond laser milling system can achieve a good processing morphology without changing the surface composition and surface hardness of dental glass ceramics. This new dental glass ceramics processing method based on ultrafast laser technique indicated a new direction for further chair processing of dental all-ceramic restoration technology.     

Synthesis of dynamic g-C3N4/Fe@ZnO nanocomposites for environmental remediation applications

An effective g-C₃N₄/Fe@ZnO heterostructured photocatalyst was synthesized by a simple chemical co-precipitation method and characterized by X-ray diffraction, Fourier transform infrared spectroscopy, transmission electron microscopy and ultraviolet–visible spectroscopy. Transmission electron microscopy revealed that 7-8 nm-sized 1%Fe@ZnO nanoparticles were evenly distributed on g-C₃N₄ nanosheets to form a hybrid composite. The photocatalytic effectiveness of the composites was assessed against methylene blue dye, and it was found that the 50%g-C₃N₄/Fe@ZnO photocatalyst was more efficient in harvesting solar energy to degrade dye than the ZnO, 1%Fe@ZnO, g-C₃N₄, g-C₃N₄/ZnO and (10, 25, 40, 60 & 75 wt%) g-C₃N₄/Fe@ZnO samples. The antibacterial competency of the samples was also explored against Gram-positive (Bacillus subtilis, Staphylococcus aureus and Streptococcus salivarius) and Gram-negative (Escherichia coli) bacteria through the well diffusion method. The 50%g-C₃N₄/Fe@ZnO nanocomposite exhibited a superior antibacterial action compared to that of the rest of the samples. The exceptionally improved photocatalytic and antimicrobial efficiency of the 50%g-C₃N₄/Fe@ZnO composite was primarily accredited to the synergic outcome of the interface established between Fe@ZnO nanoparticles and g-C₃N₄ nanosheets.     

Effects of sliding velocity on tribo-oxides and wear behavior of Ti–6Al–4V alloy

Dry sliding wear tests were performed for Ti–6Al–4V alloy on a pin-on-disc wear tester. The wear behavior of Ti–6Al–4V alloy at sliding velocities of 0.5–4 m/s was studied and the tribo-oxides and their function were explored. Ti–6Al–4V alloy presented a marked variation of wear rate as a function of velocity. With the rise and fall of wear rate, Ti–6Al–4V alloy underwent the transitions of wear mechanisms from the combination of delamination wear and oxidative wear at lower speeds to delamination wear at 2.68 m/s, and then to oxidative wear at 4 m/s. These phenomena were attributed to the appearance and disappearance of tribo-oxides. In spite of trace or a small amount, tribo-oxides would change the wear behavior, and even wear mechanism.     

Integrated sizing and scheduling of wind/PV/diesel/battery isolated systems

In this paper we address the optimal sizing and scheduling of isolated hybrid systems using an optimization framework. The hybrid system features wind and photovoltaic conversion systems, batteries and diesel backup generators to supply electricity demand. A Mixed-Integer Linear Programming formulation is used to model system behavior over a time horizon of one year, considering hourly changes in both the availability of renewable resources and energy demand. The optimal solution is achieved with respect to the minimization of the levelized cost of energy (LCOE) over a lifetime of 20 years. Results for a case study show that the most economical solution features all four postulated subsystems.